label: url

en: Sub-micrometer chemical imaging of dental adhesive/dentin interfaces via mid-infrared photothermal microscopy Author links open overlay panel

en: Optics Communications

ja: Optics Communications


en: The effect of HEMA and 10-MDP in the bonding agent of a two-step self-etch system on water sorption, elastic modulus, and microtensile bond strength to dentin

en: This study evaluated the effects of HEMA and 10-MDP in the bonding agent in a 2-step self-etch adhesive system, Clearfil SE Bond 2, on water sorption (W) and elastic modulus (E) of the polymerized bonding agent. The microtensile bond strength (µTBS) to dentin was also evaluated initially and after 10,000 thermal cycles (TC10,000). Four bonding agents were tested: the original, H-free (excluding HEMA), M-free (excluding 10-MDP), and HM-free (excluding HEMA and 10-MDP). HEMA increased W and decreased E. Initial µTBS (TC0) was highest for the original and lowest for HM-free. After TC10,000, the original maintained the highest µTBS, indicating the importance of HEMA and 10-MDP. TC10,000 did not reduce µTBS for any groups. HEMA and 10-MDP compromised mechanical property and increased water sorption, suggesting these components could potentially compromise adhesive stability.

en: Dental Materials Journal

ja: Dental Materials Journal


en: A Digitally Enhanced Transparent Silicone Index for the Direct Composite Resin Injection Technique in Premolar Replacement: A Case Report

en: Operative Dentistry, Endodontology and Periodontology


en: Effects of powder-to-liquid ratio on properties of β-tricalcium-phosphate cements modified using high-energy ball-milling

en: The authors have developed a β-tricalcium-phosphate (β-TCP) powder modified mechano-chemically through the application of a ball-milling process (mβ-TCP). The resulting powder can be used in a calcium-phosphate-cement (CPC). In this study, the effects of the powder-to-liquid ratio (P/L ratio) on the properties of the CPCs were investigated, and an appropriate P/L ratio that would simultaneously improve injectability and strength was clarified. The mβ-TCP cement mixed at a P/L ratio of 2.5 and set in air exhibited sufficient injectability until 20 min after mixing, and strength similar to or higher than that mixed at a P/L ratio of 2.0 and 2.78. Although the mβ-TCP cements set in vivo and in SBF were found to exhibit a lower strength than those set in air, it did have an appropriate setting time and strength for clinical applications. In conclusion, P/L ratio optimization successfully improved the strength of injectable mβ-TCP cement.


en: Effects of high-energy ball-milling on injectability and strength of β-tricalcium-phosphate cement

en: Calcium phosphate cement (CPC) offers many advantages as a bone-substitution material. The objective of this study is to develop a new CPC that simultaneously exhibits fine injectability, a short setting time, and high strength. β-tricalcium phosphate (β-TCP, control) powder was ball-milled for 24h to produce a new cement powder. The modified β-TCP after 24h milling (mβ-TCP-24h) exhibited excellent injectability even 1h after mixing. The mechanical properties of the set cement (compact) were evaluated using compressive strength (CS) and diametral tensile strength (DTS) testing. The CS and DTS values of the mβ-TCP-24h compacts were 8.02MPa and 2.62MPa, respectively, at 5h after mixing, and were 49.6MPa and 7.9MPa, respectively, at 2 weeks after mixing. All the CS and DTS values of the mβ-TCP-24h compacts were significantly higher than those of the control for the same duration after mixing. These results suggest that the mechano-chemically modified β-TCP powder dissolves rapidly and accelerates hydroxyapatite precipitation, which successfully shortens the cement setting time and enhances the strength. This study supports that mβ-TCP-24h is a promising candidate for use in injectable CPCs with improved strength.

en: Journal of the Mechanical Behavior of Biomedical Materials